 
Description:
The "Bridgeplane" maps the 26-pin
MicroCore-11 I/O connector to the corresponding 68HC11 signals on the Adapt11
50-pin I/O connector. It can also be used with Adapt12 boards (equivalent
pins shown in the table).
Example Uses:
-
Control any of the MicroCore-11 motor
driver boards with an Adapt11 or Adapt12 board
-
Use a 50-pin Display/Keyboard/Keypad
Interface (DKKI) card with MicroCore-11
-
some re-map jumpering required on DKKI
-
keypad circuit can't be used (not enough
I/O pins on MicroCore-11)
-
Use any Adapt-series prototyping card
with MicroCore-11 when you need a lot of prototyping area
Connector Configurations:
The standard configuration is shown
in the photo above. The connector option sequence is from front to
back (starting with the 50-pin connectors). In some cases, other
connector options make sense. For example: to add on a backplane
or ribbon cable, you might want RA or FRA in position 1 and/or position
4 (Order Code: MC11AD11BP1-RA-F-F-RA).
Ordering Information:
MC11AD11BP1-X-X-X-X
Example (shown in photo):
AD11MC11BP1-F-F-F-F
(or AD11MC11BP1-4F, for short) |
| 26-pin MicroCore-11
PIN# |
HC11 SIGNAL NAME |
50-pin Adapt11/12
connector Pin# |
HC12 SIGNAL NAME |
| 1 |
PA7 |
6 |
PT7/IOC7/PAI |
| 2 |
PA6 |
7 |
PT6/IOC6 |
| 3 |
PA5 |
8 |
PT5/IOC5 |
| 4 |
PA4 |
9 |
PT4/IOC4 |
| 5 |
PA3 |
10 |
PT3/IOC3 |
| 6 |
PA2 |
11 |
PT2/IOC2 |
| 7 |
PA1 |
12 |
PT1/IOC1 |
| 8 |
PA0 |
13 |
PT0/IOC0 |
| 9 |
VRH |
30 |
VRH |
| 10 |
PE0/AN0 |
22 |
PAD0/AN0 |
| 11 |
PE1/AN1 |
23 |
PAD1/AN1 |
| 12 |
PE2/AN2 |
24 |
PAD2/AN2 |
| 13 |
PE3/AN3 |
25 |
PAD3/AN3 |
| 14 |
PE7/AN7 |
26 |
PAD7/AN7 |
| 15 |
PE6/AN6 |
27 |
PAD6/AN6 |
| 16 |
PE5/AN5 |
28 |
PAD5/AN5 |
| 17 |
PE4/AN4 |
29 |
PAD4/AN4 |
| 18 |
GND |
49, 50 |
GROUND |
| 19 |
VRL |
31 |
VRL |
| 20 |
XIRQ* |
45 |
XIRQ* |
| 21 |
IRQ* |
46 |
IRQ* |
| 22 |
+5VDC |
47 |
+5VDC |
| 23 |
PD5/SS* |
4 |
PS7/SS* |
| 24 |
PD4/SCK |
3 |
PS6/SCK |
| 25 |
PD3/MOSI |
2 |
PS5/MOSI |
| 26 |
PD2/MISO |
1 |
PS4/MISO |
|
